Fluke 87V Industrial Digital Multimeter

The Fluke 87V Industrial Multimeter provides the resolution and accuracy to efficiently troubleshoot motor drives, plant automation, power distribution, and electromechanical equipment – even in loud, high-energy, and high-altitude locations. The 87V is designed so you can work more efficiently. Easy-access door for fast battery changes without breaking the calibration seal Analog bar graph for fast changing or unstable signals Large digit display with bright, two-level backlight for easier reading in low light Touch Hold keeps readings on display even after removing probes

FLUKE 87-V-EUR True RMS Industrial Multimeter

Rugged, high accuracy industrial multimeter to measure current, voltage and frequency on complex variable frequency drive (VFD) signals Offers true-RMS AC voltage and current for measuring non-linear signals Safety rated CAT III 1000 V, CAT IV 600 V

FLUKE 830-Shims Laser Alignment Tool – Shims

Corrects vertical misalignment. Optional accessory for the Fluke-830 Precision alignment shim kit that corrects vertical misalignment.

FLUKE 820-2 LED Stroboscope

Rugged, compact, easy to use stroboscope for checking the rotating speed of machinery without physical contact or the need for reflective tape Features high-intensity 7-LED array—4,800 Lux @ 6,000 FPM/30cm Provides a high-efficiency LED solid-state light source with uniform flash characteristics that allow for higher flash rates—30-300,000 FPM (flashes per minute)

FLUKE 810SMP Sensor Mounting Pads (10-pack)

FLUKE 810 Vibration Tester

On-board identification and location of the most common mechanical faults (bearings, misalignment, unbalance, looseness) focus maintenance efforts on root cause, reducing unplanned downtime Overall vibration level allows you to quickly assess overall machine health directly from the diagnosis screen Fault severity scale with four severity levels helps you prioritize maintenance work Repair recommendations advise technicians on corrective action Detailed diagnostic reports and spectral diagrams help confirm data quality, and narrow down the root cause of failures On-board context sensitive help provides real-time tips and guidance to new users Flexible machine speed configurations gives the ability to test a broad range of assets including belt drives, gear boxes, and bevel gears 2 GB expandable on-board memory provides enough space for your machinery’s data Self-test function ensures optimal performance and more time on the job

FLUKE 805 FC Vibration Meter with Fluke Connect

Reliable, repeatable, accurate device for checking bearings and overall vibration Features innovative sensor design that minimizes measurement variations caused by device angle or contact pressure Provides consistent data quality at both low and high frequency ranges Offers four-level severity scale to assess urgency of problems and bearing condition

FLUKE 77-4-EUR Digital Multimeter 1000V – 6000Count

Wide 1000 V measurement range Average responding AC measurements 0.3% accuracy 10 Amps continuous (20 A for 30 seconds) Frequency and capacitance Resistance and continuity

FLUKE 715 Volt/mA Loop Calibrator

Provides step and linear ramp output function Features configurable zero and span settings Provides 24V loop supply with simultaneous current measurement Features enhanced voltage and current measure and source accuracy Is EMI tolerant, dust/splash resistant and features a removable battery door for quick battery changes Includes a 250 ohm HART resistor with loop power Comes with a protective yellow holster with test lead storage Is compatible with ToolPak magnetic meter hanging system

FLUKE 710 MA LOOP VALVE TESTER

Valve test procedures that deliver Good, Marginal or Bad assessment of a control valve Generic HART communication Best-in-class mA accuracy at 0.01 % measurement or source value Compact rugged design Intuitive user interface with Quick-Set knob for fast setup, easy to use 24 V DC loop power with mA measure mode (-25 % to 125 %) Resolution of 1 μA on mA ranges and 1 mV on voltages ranges Built in selectable 250 Ω resistor for HART communications Simple two wire connection for all measurements

FLUKE 709H Precision HART Loop Calibrator

Provides resolution of 1 µA on mA ranges and 1 mV on voltage ranges Quickly transfers calibration data for documentation in either (.csv) or (.txt) format with optional 709H/Track software/cable Offers selectable capture interval from 1 to 60 seconds and a logging capacity of 9800 records or 99 individual sessions. Features small rugged design and runs on six standard AAA batteries Requires only simple two wire connection for all measurements Provides Auto Shutdown to conserve battery life (adjustable up to 30 minutes) Offers variable step and ramp time in seconds Provides adjustable span selection (0 to 20 mA or 4 to 20 mA) Includes valve test functionality (simulate defined mA values with % keys)

FLUKE 709 Precision Loop Calibrator 10 to 95% non-condensing

Provides resolution of 1 µA on mA ranges and 1 mV on voltage ranges Features a compact rugged design and runs on 6 standard AAA batteries Provides Auto Shutdown to conserve battery life (adjustable up to 30 minutes) Offers variable step and ramp time in seconds Provides adjustable span selection (0 to 20 mA or 4 to 20 mA) Includes valve test functionality (simulates defined mA values with % keys)